<< Yokogawa Universal Digital Meters & Counters

Yokogawa 800Plus
Universal Digital Meter & Counter

Customizable formats to fit your needs
Wide Choice of Measurement Items
Peak Display, Reset, and Alarm keys

Yokogawa 800Plus Shown

Product Information
Datasheet	185 KB
Ordering Info
PDF Help

The 800Plus Universal Digital Meter is a versatile, cost effective solution to a wide variety of monitoring and control applications. The input can be changed by the user to any of the DC voltage and current, AC voltage and current, RTD and Thermocouple, Process and Frequency values listed above by re-locating shorting jumpers on the plug-in signal conditioner card. No calibration equipment is required when changing ranges since they are digitally pre-calibrated at the factory. Rescaling is accomplished via front panel pushbuttons. Optional alarms and outputs are also front panel programmable.

Menu Key
The menu key steps through the various meter parameters that may be selected. These menu items may be “locked out" from front panel selection by software and hardware.

Peak Display Key (Digit Select)
In the Operating Mode, pressing the Peak Display Key causes the peak value of the input signal to be displayed. Pressing the key again returns the display to the present value. In Menu Mode ,the Digit Select Key (Peak Display Key) is used to select input type and decimal point or to select one of the five display digits for programming. In the main menu, pressing the Digit Select Key causes the value or code that is stored for that menu item to be displayed and the left hand digit flashes. Each time the key is pressed, the next digit to the right will flash. The value of the flashing digit may be changed using the Value Select Key. In the Alarm Mode, pressing the Digit Select Key causes the most significant digit of the displayed set point value to flash. Digits are then selected the same as in the Menu Mode.

Reset Key (Value Select)
In the Operating Mode, holding the Reset Key depressed and pressing any other key causes are set to occur. The Menu Key resets all meter functions, the Alarm Key resets any alarm conditions and the Peak Display Key resets the peak value to present value. In the Menu Mode or Alarm Mode, the Value Select Key (Reset Key) sets the value of the flashing digit. Each time the key is pressed, the value increases by one. Holding the key down causes the digit to automatically step through the numbers.

Alarm Key (Reverse Menu)
In the Operating Mode, pressing the Alarm Key displays the set-point of Alarm 1 and then Alarm2. These values may be changed using the Digit Select Key and the Value Select Key. In the Menu Mode, pressing the Alarm Key steps the display backward through the menu.

800Plus Universal Digital Meters
Specifications		FR Counter/Timer	VF Counter/Timer	QD Quaduture Input
Display	# of Digits	6 digits
	Range	-99999 to +99999
	LED Indicators	3 status indicators
	Color	Red or Green
Accuracy	Full scale or reading	±2ppm	0.015%FS	±2ppm
	Span TEMPCO	0.003% of reading/°C- except load cell(0.0015% rdg./°C) & FR(±1ppm/°C typical)
	Zero TEMPCO	0.001FS/°C
Conversion	General	1 / period time: Gate time + 30ms + 2 periods of the input signal (max): gate time selectable 0 to 199.99 seconds
Noise Rejection	General	Common Mode voltage from DC to 60 Hz safety rated to 250 VAC; 4.2 kVp per high voltage test
Case		NEMA 4 (IP65) 1/8 DIN case made of high impact 94V-0 UL rated plastic
Environmental		Temperature: Operating0°C~55°C, Storage-40°C~85°C; Relative humidity 95% at 40°C non-condensing
Operating Power	General	Frequency 47 to 440 HZ and DC, consumption 5.3 Watts maximum
	Standard	Universal power supply 85 to 264 VAC, 90 to 370 VDC
	Option	Universal power supply 8 to 28 VAC, 9 to 37 VDC
Frequency	General	Selectable with shorting jumpers on power supply printed circuit board (normal setting 10 VDC)
	Outputs	5 VDC, ±5%, 100 mA max., 10 VDC, ±5%, 120 mA max., 24 VDC, ±5%, 50 mA max.
	Isolation (power ground)	Safety rated to 250 VAC, 4.2 kV peak per high voltage test
Dual Controller Option	General	NEMA 4 (IP65) 1/8 DIN case made of high impact 94V-0 UL rated plastic
	Setup	Set point values may be entered from front panel pushbutton or via RS-232 or RS-485
	Output Operation	Either may be set to operate above or below set point, latching or non-latching, or output disabled
	Filtering	Comparison to the set points may be from filtered or unfiltered input signal
	Time Delay	Selectable time delay of output status change from 1 to 128 readings
	Lockouts	Pushbutton control of display and change of set points, or display of set points, or disable
	Alarm Status Indicators	Either of two red LED’s may be set to indicate when output is on or off, or they may be disabled
Relay Output	General	10 A at 240 VAC, 8 A at 24 VDC contact rating; safety certification: VDE, UL, CSA
	Isolation	Coil to contacts :Safety rated to 250VAC, 4.2 kV peak; Between open contacts :Withstand 1 kVrms
	Response to input signal	Pick-up:26 milliseconds typical; Release:22 milliseconds typical
Optotransistor output	General	Voltage rating:30VDC; Current rating:100 mA minimum at 1.2 VDC maximum
	Isolation	Safety rated to 250 VAC, 4.2 kV peak per high voltage test
	Response to Input Signal	17 milliseconds typical
Analog Output Option	General	Power :provided by meter, Isolation: Withstand 3750 Vrms, 8mm creepage
	Accuracy	Use basic meter accuracy ±0.05% of analog output full scale
	Response Time	17 milliseconds for unfiltered input, same as basic meter for filtered output
RS-232/RS-485	General	Power :provided by meter; Isolation: safety rated to 250 VAC, 4.2 kVp per high voltage test
	Baud Rates	300, 600, 1200, 2400, 9600, 19200
	Type/Signal Levels	Full duplex (RS-485) / meets RS-232 and RS-485 standards
BCD Output	General	Power : provided by meter; Isolation: safety rated to 250 VAC, 4.2 kVp per high voltage test
	Type/Signal Levels	Tri-state, stored parallel / LSTTL, CMOS compatible
	Controls	BCD Enable, Hold, Data ready
Ordering Info		More Info>>

Ordering Information
Model	Description	Price
800Plus	Yokogawa 800Plus Universal Digital Counters	Please Call

Yokogawa 800Plus Universal Digital Meter & Counter

Yokogawa 800Plus
Universal Digital Meter & Counter