|
|
|
|
|
|
|
|
<< HP 4195A Product Page
Agilent / HP 4195A |
| Source | |
| NETWORK MEASUREMENT | |
| Frequency | 10Hz to 500MHz, 1mHz resolution |
| Power | -50dBm to +15dBm, 0.1dB resolution |
| Sweep Parameters | Frequency, power and dc bias level |
| Sweep Types | Linear, log. cw, program and partial |
| Output | 2 outputs |
| DC bias level | ±40V, 10mV resolution |
| Receiver | |
| Frequency | 10Hz to 500MHz |
| Input | 4 inputs, 50 Ω nominal |
| Resolution Bandwidth | 3Hz to 300kHz, 1 or 3 step |
| Input Crosstalk | ≤ -100dB |
| Magnitude Ratio | |
| Dynamic Range | > 100dB |
| Resolution | 0.001dB |
| Dynamic Accuracy (23 ± 5°C), -30dBm R input | ±0.05dB @ -70dBm to -30dBm T input |
| Phase | |
| Range | ±180° |
| Resolution | 0.01° |
| Dynamic Accuracy (23 ± 5°C, -30dBm input) | ±0.3° @ -70 to -30dBm T input |
| Delay | |
| Range | 10ps to 500s |
| Resolution | 10ps @ 3.6 MHz aperture |
| Accuracy | depends on phase accuracy |
| Error Comprehension | |
| Mode | Normalization, 1 port partial cal, 1 port full cal and port extension |
| SPECTRUM MEASUREMENT | |
| Frequency | |
| Measurement Range | 10Hz to 500MHz |
| Resolution | RBW: 3Hz to 300kHz,
1 or 3 step Selectivity (60/3dB): 4 for 3Hz to 30Hz 8.5 for 100Hz |
| Amplitude | |
| Measurement Range | -135 dBm to +20dBm |
| Accuracy | ±1.0dB @ 50MHz |
| Linearity (23 ± 5°C) | ±0.1dB @ -40 to 0dB; ±0.2dB @ -60 to -40dB |
| Frequency Response | ±1.5dB |
| Dynamic Range (23 ± 5°C) | |
| Second Harmonic Distortion | ≤ -70dBc @ ³ 2MHz |
| T.O.I. Distortion | ≤-80dBc @ ³ 2MHz |
| Residual Response | -110dB @ ³ 100kHz |
| Average Noise Level | typically -140dBm @ 10Hz RBW, ³ 2MHz |
| Sweep | |
| Sweep Type | Linear, log, cw, program and partial |
| Sweep Mode | Continuous, single and manual |
| Sweep Time | approximately 500 ms/span to 1800 s/span |
| Input | |
| Number of inputs | 4 inputs |
| Impedance | 50 Ω nominal |
| Damage level | +30 dBm |
| Attenuator | 0 to 50dB, 10dB step |
| DISPLAY AND ANALYSIS | |
| Display | 7.5 inch color CRT |
| Display Format | Rectangulars, Table, Smith and Polar |
| Traces | 4 traces max |
| Scale Type | Linear, log |
| Autoscale | |
| Phase display Expansion | Display phase continuously more than ± 180 deg. |
| Video Filter | Digital video filtering reduces random noise |
| Comment Entry | Display a comment used alphabet, numeral and special characters (, , %, etc.) |
| Marker | MKR ® Max (Min, Ref, Center, Start and Stop), Next Peak, Width and Delta reading mode |
| USER FUNCTIONS | |
| User Math | Puts the result in the form needed for your application by using built-in math operators, arithmetic functions and editing capability. |
| User Defined Function | Provides one-key solution for a specific application without an external computer. 6 user functions can be created and soft-keys can be labeled as you like. |
| User Program (Auto Sequence Program) | Allows to program the control or measurement, analysis, copy and other sequence without an external computer. |
| HARDCOPY | |
| Dump Mode | Copy the CRT display to a graphics printer |
| Plot Mode | Copy the traces, graticule and annotations to an HP-GL compatible digital plotter |
| Print Mode | Copy measurement data in tabular form to a printer |
| Hardcopy of traces, measurement data, results of analysis and annotations are produced by the 4195A and HP plotters or printers with LISTEN only capability. | |
| STORAGE | |
| Instrument
state, trace data, table of Program Sweep and User Program can be
independently saved or recalled from the built-in 3.5 inch floppy disk
memory via SAVE/GET function. Instrument state includes active control setting of measurement, active calibration data, active display format, active scale setting, User Math and User Define Function. |
|
| REMOTE PROGRAMMING | |
| Interface Function | SH1, AH1, T5, TE0, L4, LE0, SR1, RL1, PP0, DC1, DT1, C0, E1 |
| Transfer Formats | ASCII 32/64 bit IEEE 754 floating point format |
| HP-IB interface operates according to IEEE 488-1987 and IEC 625 standards and IEEE 628-1982 recommended practices. | |
| GENERAL CHARACTERISTICS | |
| Operating Conditions | |
| Temperature | 0°C to +45°C |
| Humidity | 95% RH at 40°C |
| Non-Operating Conditions | |
| Temperature | -40°C to +70 |
| Safety | Based on IEC-348, UL-1244 |
| Power | 100, 120, 220V ±10%, 240V -10% +5%, 48Hz to 60Hz, 500VA (max) |
| Dimensions | 425 (W) X 375 (H) X 620 (D) mm |
| Weight | approximately 41kg |
$20.00 Minimum on Total Order
Home Page | Test Equipment Catalog | Specials | Repair
We Buy Surplus | Ordering/Contact Info
____________________________________________________________
99 Washington Street, Melrose, MA 02176
781.665.1400 | 800.517.8431 | Fax: 781.665.0780 | Email:
Copyright © Fotronic Corporation All Rights Reserved
