<< Tektronix Accessories | << Tektronix Oscilloscope Probes | << Tektronix Current Probes
<< Tektronix Probes & Accessories Price List
Tektronix TCP0150
AC/DC Current Probe with TekVPI Interface
|
 
TCP0150 AC Current Probe Shown
|
Features & Benefits
- Easy-to-Use and Accurate AC/DC Current Measurements
- Connects Directly to DPO4000, MSO4000, and DPO7000 Series
Oscilloscopes Using the TekVPI Probe Interface
- DC to 20 MHz Bandwidth
- 150 ARMS
Maximum Current Capability
- 500 A Peak Pulse Current Capability
- High Accuracy with Typically Less Than 1% DC Gain Error
- Accurately Measures Current levels as Low as 5 mA
- Low Noise and DC Drift
- Provides Automatic Units Scaling and Readout on the
Oscilloscope's Display
- Remote Programmable GPIB Control for ATE systems
- Split-core Probe Head Construction Allows Easy Connection
to Conductors
- Easy to Degauss and Autozero
- Setup Controls and Probe Status and Diagnostic Indicators
are Provided on Both the Probe Hardware and through an Easy-to-Access
Scope UI Display Menu
Applications
- Power Supplies
- Semiconductor Devices
- Power Inverters/Converters
- Electronic Ballasts
- Industrial/Consumer Electronics
- Motor Drives
- Transportation Systems
- Note: Requires DPO7000 Series Firmware Version 3.0.2 or
greater. Requires MSO/DPO4000 Firmware Version 2.06 or greater.
Tektronix TCP0150 is a high performance and easy-to-use 150 A AC/DC
current probe designed for use and direct connection (without the need of
an additional power supply) to the TekVPI™ probe interface used on
Tektronix DPO4000, MSO4000, and DPO7000 Series oscilloscopes. This AC/DC
current measurement probe provides 20 MHz of frequency bandwidth with
selectable range control for 25 A and 150 A measurement ranges. It also
provides low-current measurement capability and accuracy to current levels
as low as 5 mA per division – important for achieving broad dynamic
current range of high-level and low-level measurement signals.
Specifications
|
Characteristics
Warranted
- Bandwidth: DC to ≥20 MHz (-3 dB). Derate
with Frequency. See Figure 1. (Calculated from Rise Time BW =
.35/Rise Time)
- Rise Time: ≤17.5 ns
- Max RMS Current: 150 A
- Max Peak Pulse Current: 500 A
- Minimum Sensitivity: 5 mA (on
oscilloscope’s 1 mV/div setting); AC Coupling (on
oscilloscopes that support AC/DC coupling)
- Current Ranges: 25 A and 150 A
- Max Bare-wire Voltage: 600 VRMS
CAT I and II; 300 VRMS CAT III
Typical
- DC Accuracy: ±1% Typical; 3% Warranted
- Max Amp-second Product:
- 25 A Range: 3,000 Aµs
- 150 A Range: 15,000 Aµs
- Insertion Impedance: 0.03 Ω at 1 MHz;
0.075 Ω at 5 MHz; .125 at 10 MHz; .3 at 20 MHz
- Signal Delay: 21 ns
- Displayed RMS Noise: ≤500 μARMS
(probe only)
|
Environmental
- Temperature:
- Operating: 0 ºC to +50 ºC
- Nonoperating: -40 ºC to +75 ºC
- Humidity
- Operating: 5% to 95% RH (Relative
Humidity) at up to +30 ºC; 5% to 85% RH above 30 ºC up to
+50 ºC, noncondensing
- Nonoperating: 5% to 95% RH (Relative
Humidity) at up to +30 ºC; 5% to 85% RH above 30 ºC up to
+75 ºC, noncondensing
- Altitude
- Operating: Up to 2,000 meters
(6,560 feet)
- Nonoperating: Up to 12,000 meters
(40,000 feet)
Physical Characteristics
- Cable Length: 79 in.
- Probe head size:
- Length: 10.55 in.
- Width: 1.6 in.
- Height: 6.13 in.
- Max Conductor Diameter: 0.83 in. x 1.0 in.
- Shipping Weight: 1.734
- Power Requirements: TCP0150 is powered
directly by the DPO4000, MSO4000 and DPO7000 Series
oscilloscopes using TekVPI interface
|
|
|
|
Recommended Oscilloscopes: DPO4000, MSO4000, and DPO7000 Series
oscilloscopes with TekVPI probe interface.
Note: Requires
DPO7000 Series Firmware Version 3.0.2 or greater. Requires
MSO/DPO4000 Firmware Version 2.06 or greater.
|
|
|
|
| Ordering Information |
| Model |
Description |
Buy Online |
Price |
| TCP0150 |
Tektronix TCP0150 Probe, 150A AC/DC Current, w/ TEKVPI Interface, DC TO 20 MHZ Bandwidth - Certificate of traceable calibration standard |
 |
Sale $3,537.00
(Reg. $3,930.00) |
| Included Accessories |
| |
- (1) Protective Cover (016-1924-xx)
- (1) Certificate of Traceable Calibration and Data Standard
|
Included |
| Options |
| TCP0150OptL0 |
Tektronix Opt. L0 Standard English Language
Instruction Manual (071-xxxx-xx) |
Please Call |
| TCP0150OptL5 |
Tektronix Opt. L5 Substitutes Japanese Language
Instruction Manual |
Please Call |
| TCP0150OptL7 |
Tektronix Opt. L7 Substitutes Simplified Chinese Language Instruction
Manual
|
Please Call |
| Recommended Accessories |
| 0671701xx |
Tektronix 067-1701-xx TekVPI Calibration Fixture |
Please Call |
| 0671686xx |
Tektronix 067-1686-xx Cal/Deskew Fixture for
DPO7000/70000 Series |
Please Call |
|
)
PDF
Help