| Specifications |
| Vertical Specifications |
| Channels |
2 |
| Bandwidth |
200MHz |
| Rise Time |
1.7ns (Approx.) |
| Input Impedance |
Resistance: 1 M +/- 2%
Capacitance: (20+/-5) pF |
| Polarity |
Normal & Invert |
| Maximum Input |
400V (DC + AC Peak) |
Waveform Signal
Process |
CH1 +/- CH2, CH1 x CH2, CH1/CH2, FFT |
| Bandwidth Limit |
20MHz +/-% Typical |
| Horizontal Specifications |
| Sampling Rate |
1GSa/s
Equivalent Max. Sampling Rate is 25GSa/S for all Times |
Range
(1 - 2 - 5 Increments) |
50s/div ~ 1ns/div |
| Mode |
Main Sweep, Main Sweep + Delay Expansion Sweep, X-Y |
| Trigger Specifications |
| Source |
CH1, CH2, EXT., EXT/5, AC Line |
| Mode |
Auto, Normal, Single |
| Trigger Sensitivity |
DC: CH1/2 (typical) 1 Div from DC to 10MHz; 1.5div from 10MHz to full
EXT (Typical): 200mV from DC to 40MHz
EXT/5 (Typical): 1V from FC to 40MHz
AC: Attenuates signal below 10Hz
HF Reject: Attenuates signals below 15kHz
LF Reject: Attenuates signals below 150 kHz
Noise Reject: Reduces trigger sensitivity |
| Trigger Level Range |
CH1, CH2: +/- Division from center of screen
EXT: +/- 1.2V
EXT/5: +/- 6V |
Trigger Level Accuracy
(Accuracy is for signals having
rise and fall time at max 20ns) |
CH1, CH2: +/-(0.3div x V/div)(within +/-4 Division from center of screen)
EXT: +/- (6% of Setting + 40mV)
EXT/5: +/- (6% of setting + 200mV) |
| Edge Trigger |
Rising, Falling, Rising & Falling |
| Pulse Width Trigger |
Trigger (when >, <, =) on positive or negative pulses
Pulse width range: 20ns ~ 10s |
| Videon Trigger |
Trigger on NTSC, PAL, or SECAM standard video signal
Line Range: 1-525 (NTSC), 1 - 625 (PAL/SECAM) |
| Slope Trigger |
Trigger (when >, <, =) on positive or negative slope, Set Time: 20ns ~ 10s |
| Overtime Trigger |
From the rising or falling edge, Set Time: 20ns ~ 20s |
| Alternative Trigger |
Internal Trigger on edge, pulse width, video or slope |
| Cursors and Measurement |
| Voltage Measurement |
Vpp, Vamp, Vrms, Vhi, Vlo, Vmax, Vmin,
Pre-shoot, Overshoot |
| Time Measurement |
Frequency, Rise Time, Fall Time, Positive
Width, Negative Width, Duty Cycle |
| Delay Measurement |
Delay 1- > 2 
Delay 1- > 2  |
| Cursor Measurement |
Voltage Difference between cursors  V
Time Difference between Cursors T
Frequency difference between Cursors 1 T |
| Display |
| TFT LCD Type |
7.0 Inch Diagonal
Crystal Display |
| Display Resolution |
800 x 480 Dots |
| General Specifications |
| USB |
USB Host / USB Device |
| Power Source |
AC 100V ~ 240V +/- 10%, 45Hz ~ 440Hz,
Auto Selection |
| Physical Dimensions |
12.3 x 4.25 x 5.6" inches (313 x 108 x
142mm) |
| Weight |
4.6lbs (2.08Kg) |
)
PDF Help