PTV/DK-Technologies PM 5639/20
Industrial CRT Color Analyzer Specifications

• Luminance 0.1 to 300 cd/m² (0.03 to 100 ftL)
• x and y values: 0.000 to 0.800
• Correlated Color Temperature: 1.900 K CCT to 12.000 K CCT

• The following specifications apply to a measurement with an illuminant D6500 standard monitor¹* at a luminance level of 10 cd/m² (3ftL) and at an ambient temperature between +15°C (+59°F) and +30°C (86°F)
• xy coordinates: Better than ± 0.002
  -Repeatability: Better than  ± 0.002
  -Luminance (Y): Better than ±2% ± 1 digit
  -Repeatability: Better than ± .03%, ± 1 digit
• XYZ/RGB bars: Better than ±1%
  -Repeatability: Better than ±1%
  Luminance (Y): Better than ±2%, ± 1 digit
• Measuring rate: 3 to 10 measurements/second
• Settling time: Within 1% after 1 second
• Correlated color temperature: ±50 K CCT

¹*Calibration of the standard monitor is traceable to international light standards

• References: The white references are stored in the controlling computer. The number of white references are limited only by the computer. Legal values for x and y are between 0.200 and 0.600
• CRT/Phosphors: 30 different phosphors may be stored in the color sensor. Additional phosphors may be stored in the PC. Phosphors may be stored vial the "Learn phosphor" function. (only applicable when using the RGB bar display)
• Set-ups: An unlimited number of measuring setups may be stored in the C. A measuring setup includes the display mode, CRT/phosphor, white reference, and measuring units
• Measurements: An unlimited number of measurements may be stored for later investigation and statistical analysis
  Stored measurements may also be used as white references

• White ref.:
  -D6500 (x=o.313, y=0.329)
  -3200 K (x=0.423, y=0.399)
  -9300 K (x=0.285, y=0.293)
• Other white references may be stored using the "Learn white reference" function, as measurements or put directly in the file containing the white reference

• The color sensor is powered from a power supply box inserted between the PC and the color sensor
• Mains consumption:
  85-250 V AC 15 VA. 48 to 65 Hz

• Operating temperature:
  10°C to +40°C (+50°F to +104°F) (non-condensing)
• Storage temperature: 
  -10°C to +70°C (-14°F to 158°F)
• Vibration: IEC 68-2-6 F; 5-50-200 Hz
  0.7 mm p-p 50 m/s²; 1 oct/min; 3x30 min
• Bump: IEC 68-2-29 part 2; 350 m/s²
  1000 bumps in 3 directions
• Repetitive bump: 120 m/s²

• Color Sensor:
  Diameter of house: 108 mm (4.25")
  Diameter of rubber shadow pad: 120 mm (4.75")
  Height: 70 mm (2.75")
  Weight: 250 g (0.55 lbs)
• Power supply box:
  Size: 185x95x65 mm (7.3"x3.8"x2.6")

• IBM PC AT/386/486/Pentium, PS/2 or compatible
• 512 bytes RAM
• One floppy disk drive (5-1/4" or 3-1/2")
• MS-Dos, PC-DOS or DR-DOS (version 3.3 or higher)
• For full use of the display facilities a 100% compatible IBM EGA/VGA graphic adapter is recommended
• The software can be run from a floppy disk but a hard disk is recommended