• Ultra-portable, easy to use design
• High quality, 16:9 built-in screen for video monitoring
• Rechargeable lithium battery delivers 1-2 hours operation and mains power also available
• Superior ease of use with color coded GUI
• Lightweight at 0.9kg
• Rugged aluminium case for demanding broadcast environments
• Dual-link 3G/HD/SD-SDI designed for video technology manufacturing and production applications

Generator

• Video Generator
  • Create video test signals for all supported SD and HD SDI output standards including 3GHz standards at 1080p/50/59/60 Y, Cb, Cr
  • Advanced video formats include support for RGB, XYZ 12bit and 2K formats
  • Fully programmable Y Zone Plate
• Audio Generator
  • Embed audio signal on all 16 embedded audio outputs
  • Audio Group menu controls which audio channels are present, signal type and amplitude
  • Choice of: silence, adjustable tone, noise, AV Delay, Dolby test stream or AES input
• Reference
  • Create video test signals that are either free-running or locked to studio reference or input signal
  • Genlock menu is used to select locking reference and provides control for genlock phase offset in lines and pixels

Analyzer

• Picture Monitor
  • Picture is displayed in window adown-converted display
  • Cursor may be turned ON over area of picture specified by specific line and sample
  • Monitor device input or output
• Picture Zoom
  • Zoom function provides 1:1 unfiltered pixel view, centred on position of picture cursor
  • HANC/VANC areas visible when cursor in blanking
• Linked Cursors
  • Picture cursor is linked to waveform, vectorscope and data views for rapid and accurate detailed measurement of signal
• Waveform Full Frame
  • Displays selected analyzer or generator source
  • YCbCr GBR, Y, Cb, Cr, R, G, B modes
  • Cursors may be displayed over the waveform to allow measurement of time or amplitude values
  • Vertical and horizontal magnifications
• Waveform Line Select
  • Display may be restricted to single line or all lines may be displayed simultaneously
  • Single line display is linked to picture, vectorscope and data view
• Vectorscope
  • Choice of 100% or 75% graticules
  • Display Composite, SDI, SFP video input or generator test pattern
  • Display specific video line linked to picture cursor
  • 1, x2, x5 or x10 magnifications with position to centre, cyan, yellow, green, magenta, red, blue graticule locations

Control

• Screen Grab
  • Screen grabs can be saved and downloaded via web browser or FTP transfer
• Web Browser
  • View and control instrument display over TCP/IP interface with standard browser
  • Ideal for remote location checking, engineering support, and fault analysis
  • Allows access to key functions including screen dumps, loudness files and logging files
• PC Simulator
  • Free simulator PC application is available for download
  • Indicates command IDs for automation programming

Audio

• 16 Channel Audio Meters
  • Display up to 16 audio channels
  • Source for each block of 8 meters may be independently set to allow metering of embedded audio inputs or outputs
  • Current audio level in dBFs (decibels relative to 0dB full-scale) is displayed at bottom of each meter
• AES/Analog Audio Meters
  • Dolby E metering selection
• Audio Channel Status
  • Audio Status menu shows the Channel Status for selected audio channel
  • Displayed in decoded form as well as raw hexadecimal data dump
  • Source may either come from input signal or from generator output for rapid comparison purposes

System

• Instrument Presets
  • Current instrument settings can be saved as memories for future recall
  • Memories can be exported to single files, reimported or copied to other units
  • Presets can be applied to whole instrument or selectively within Generator or Analyzer
• Network Configuration
  • Network menu allows instrument to be configured as part of network
  • Support for automatic acquisition of network parameters via DHCP or manual configuration
  • Remote control enable/disable and selection of port number
• Software Status
  • Serial number, instrument MAC address, version information and battery state listed
  • Date and time can be set and factory default settings recalled
  • Display of loaded license options
  • LCD brightness and screen saver configurations
• Engineer Setup
  • Manage instrument's settings including user access, clearing memories, factory default reset, software upgrades and audio calibration
  • SDI input to SDI output loop through mode
• Utils
  • Details of the unit's operating status
  • Details the temperature and individual board voltages
  • Lists any hardware errors that have been recorded

Signal

• Video Timing
  • Display relationship between selected video input with respect to external reference input
  • Offset feature to simplify system timing measurements
• Video Status
  • Display the status of the selected video input or output and any errors that have been found in data stream
  • Display of EDH, Active Picture and CRC data with cumulative run-time display of errors and error rate
  • Display of estimated cable length for SDI inputs with selectable cable type
• ANC Status
  • Shows which ANC packets are present on SDI input and whether any errors have been detected
  • Each field is color coded according to whether ANC packet is present (White), missing (Grey), has errors (Red), or has previously had errors (yellow)
• Video Format/Payload ID
  • Misc Status menu displays status of SMPTE 352 packets embedded in selected video input and displays any errors that have been found
  • Selection of input or output for rapid comparison
  • Display of raw data and decoded form

Logging

• Log Setup
  • Set Audio Thresholds and log specific video status events, including Output, Reference and Input Status, TRS Errors, Picture CRC
• Event Log Display
  • Event Log menu displays list of events with time stamp showing when they occurred
• ANC Log Setup
  • Log ANC Status menu allows customization of which ANC packets to log for changes in status (e.g. Present, Checksum Error, Missing, Parity Error)
  • Logging of Dolby and AES Status as well as device system errors
  • Control of logging duration