- Single-output high-speed battery-simulating DC power supply
- 45W output (15V @ 3A, 9V @ 5A)
- Syncs up to 2A
- Optimized for battery-powered device testing
- Ultra-fast transient response to load changes
- 5A continuous output
- Pulse peak, average, and baseline current measurements
- 100nA DC current sensitivity
The Keithley 2303NMS 45W High-Speed Precision Readback Power Supply (No Manual) provides both voltage control and power consumption monitoring for automated testing of portable, battery-operated devices. This power supply is optimized for testing battery-operated, wireless communication devices such as cellular phones that undergo substantial load changes for very short time intervals. The 2303-NMS exhibits outstanding voltage stability during pulse load changes and can simultaneously measure load currents, even if they are short pulses. In addition, this power supply can sink current and thus, it can take on the characteristics of a discharged, rechargeable battery for testing chargers and charger-control circuitry.
5A Output Capacity
The 2303-NMS can supply 5A at 9V to serve the peak pulse loading requirements of battery-operated devices. The 2303-NMS can deliver a maximum current of 5A continuously; it can also supply up to 15V.
Fast Response to Load Changes
Keithley's High Speed Power Supplies are designed to simulate the current drive capacity of a battery. The power supplies simulate a battery's response during a large load change by minimizing the maximum drop in voltage and recovering to within 100mV of the original voltage in 40μs or less.
When a portable device such as a cellular phone switches from standby mode to the full power mode of operation, the current draw on the power supply can change by as much as 1000%. While a battery's voltage will decrease by the value of the voltage drop across the battery's low internal resistance, a conventional power supply will have a significant voltage drop (more than one volt) and take milliseconds to recover to the original voltage level. For portable devices that operate at full power only for short intervals, the full power event is over before a conventional power supply can recover. For example, cellular phones designed in accordance with the GSM cellular phone standard transmit and receive information in 576μs pulses. If the power supply used to test them cannot recover quickly enough, the performance of the deviceunder - test will be compromised by the power supply. If the power supply voltage drops below the threshold of the phone's low-battery detection circuitry for a sufficient amount of time, the phone will turn off during testing, giving a false indication of a failed device.
The Models 2303-NMS's fast transient response to large load changes will enable test engineers to test their portable products properly and eliminate false failures due to conventional power supplies with slow response times. In this way, the power supply ensures maximum production throughput when testing portable devices.
Fast Measurements for Power Consumption Analysis
As manufacturers of portable devices strive to extend battery life and the length of time between recharges, power consumption has become an important performance indicator. Therefore, in production testing, accurate peak power and average power measurements are critical. These measurements are complicated by the fact that wireless telecommunication devices draw full load current in short pulses. The 2303-NMS's pulse readback measurement mode makes it possible to capture peak and average values on pulses as short as 60μs. This allows the power supply to power a device-under-test and determine its current consumption to qualify the device for its specified power consumption.
In addition to making measurements on short pulses, the 2303-NMS power supply can measure a current pulse peak or a current pulse train that is as long as 833ms. For random pulse trains that have periods longer than 833ms, the power supplies have a special, elongated integration mode that can make an average current measurement on up to 60s of data.
Accurate Low-Current Measurement
The 2303-NMS is well-suited for making fast, accurate measurements of sleep and standby mode currents because it is based on Keithley's expertise in low-current measurement technologies. With 100nA resolution, the power supplies offer the precision needed to monitor the low sleep mode currents in today's products and in future products. It can also measure these low-currents with 0.2% basic accuracy.
High-Current Sinking Capacity
The 2303-NMS can act as an electronic load and sync as much as 2A, so it can simulate a discharged rechargeable battery. Therefore, they can be used to verify the performance of a portable device's charger. The power supply's current dissipation capacity allows it to test even high-current fast chargers.
Independent Digital Voltmeter Inputs
While many programmable power supplies offer output readback capabilities, Keithley's power supplies are the only instruments available that also offer a set of DVM inputs. These inputs allow the Model 2303-NMS to measure signals from 0 to +/-15V anywhere in the test system with the same rated accuracy as the voltage readback. The DVM and the power source can operate simultaneously. For many applications, the power supply's built-in DVM eliminates the expense and space that a separate voltage measurement instrument requires.
|CS-846||Tek Video CS-846 5-8 ft. MSTB 2 5/8-STF-5 08 Cable||
|SC-182||Tek Video SC-182 Low Inductance Coaxial Cable (Safety Controlled)||
|4288-1||Keithley 4288-1 Single Fixed Rack Mount Kit||
|4288-2||Keithley 4288-2 Dual Fixed Rack Mount Kit for Models 2000, 2700, and 6487||
|KPCI-488LPA||Keithley KPCI-488LPA IEEE-488.2 Interface Module for PCI Buses||
|KUSB-488B||Keithley KUSB-488B IEEE-488.2 USB-to-GPIB Interface Adapter for USB Ports||