- 6-Channel model with motor analysis and D/A output included
- Basic accuracy of +/-0.02% for power measurement (PW6001 accuracy only. Instrument delivers accuracy of +/-0.07% even after the current sensor accuracy has been added.)
- High noise resistance and stability (80 dB/100 kHz CMRR, +/-0.01%/ C temperature characteristics)
- Accurate measurement even when the load is characterized by large fluctuations; TrueHD 18-bit resolution
- 10 ms data refresh while maintaining maximum accuracy (using a specially designed IC to make all measurements independently while performing simultaneous calculations.)
- DC basic accuracy of +/-0.07%, which is key for stable, accurate efficiency measurement
- Broad frequency band and sampling that are 10 times better than those of legacy models
- Synchronize 2 units for up to 12 channels in real time
- Models can be connected with an optical connection cable (over a max. length of 500 m) to enable numerical and waveform synchronization.
- Special triggers to enable waveform analysis and motor analysis without the need for an oscilloscope
Hioki PW600116 benchtop power analyzer is a 6 Channel power measuring instrument with D/A output and motor Analysis functions. The PW6001-16 features high accuracy, wide band, and high stability for measuring electrical power from DC to inverter frequencies. Optional voltage cords and current sensor are required for taking measurements.
0.1 Hz to 2 MHz frequency bandwidth
Power measurements across wide bandwidths are required for supporting high-speed switching devices such as SiC. Compared even to the Hioki 3390 Power Analyzer, the PW6001 is engineered with 10x the frequency band and sampling performance. High accuracy, wideband, and high stability. The Hioki PW6001 combines the 3 important elements of power measurement and basic performance backed by advanced technology to achieve unsurpassed power analysis.
High-speed sampling of 5 MS/s for true frequency analysis
Measurements based on sampling theorem are required to perform an accurate power analysis of PWM waveforms. The Hioki PW6001 features direct sampling of input signals at 5 MS/s, resulting in a measurement band of 2 MHz. This enables analysis without aliasing error.
Fast, simultaneous calculation functions achieved with Power Analysis Engine II
All measurements, including period detection, wideband power analysis, harmonic analysis, and waveform analysis, are digitally processed independently and with no effect on each other. Fast calculation processing is used to achieve a data update speed of 10 ms while maintaining maximum accuracy.
Analyze waveforms without an oscilloscope
In addition to voltage and current waveforms, torque sensor and encoder signals can also be displayed simultaneously. The PW6001 is also built in with triggers, pre-triggers, other triggers convenient for motor analysis such as for PWM waveforms, as well as encoder pulse triggers.
Harmonic analysis up to 1.5 MHz
Wideband harmonic analysis is provided as a standard feature to a max. 100th order for fundamental frequencies 0.1 Hz to 300 kHz and an analysis band of 1.5 MHz. Analysis of fundamental waves in motors and measurement of distortion rate in the transmission waveforms for wireless power supplies are now possible.
Specially designed for current sensors to achieve highly precise measurement
This reduces the effects of wiring and meter loss, allowing measurements with wiring conditions that are close to the actual operating environment for a highly efficient system. - Short wiring, Little effect from routing, Small insertion loss.
High-accuracy clamp current sensor
The CT684x series feature broad temperature characteristics and an operating temperature range of -40°C to 85°C, allowing them to be used in operational evaluations of devices and inside equipment that are subject to extreme temperature changes. The current sensors’ tough performance helps ensure you can make the measurements you need.
Time spent on operations is reduced, to allow focused concentration on analysis. The PW6001 has a 9" touch screen with soft keypad and dual knobs for vertical/horizontal manipulation of waveforms. The built-in easy setup function allows you to simply select the type of measurement line and immediately start measurement using the automated optimum settings.
Diverse motor analysis functions
Enter signals from torque meters and speed meters to measure motor power. In addition to motor parameters such as motor power and electrical angle, output signals from insolation meters and wind speed meters can also be measured.
D/A output supporting wavefrom output
Output analog measurement data at update rates of up to 10ms. Combine with a data logger to record long-term fluctuations, and use the built-in waveform output function to output voltage and current at 1 MS/s. (During waveform output, accurate reproduction is possible at an output of 1 MS/s and with a sine wave up to 50 kHz.)
|3273-50||Hioki 3273-50 Wideband DC to 50 MHz/30A AC/DC Current Probe||
|3276||Hioki 3276 Wideband DC to 100 MHz/30A AC/DC Current Probe||
|3275||Hioki 3275 Wideband DC to 2 MHz/500A AC/DC Current Probe||
|3274||Hioki 3274 Wideband DC to 10 MHz/150A AC/DC Current Probe||
|9151-02||Hioki 9151-02 GP-IB Connector Cable (2 Meter)||
|9243||Hioki 9243 Grabber Clips, Red and Black||
|9444||Hioki 9444 Connection Cable for the 9442 Printer||
|9637||Hioki 9637 RS-232C Cable for PC, 9 pin - 9 pin, Cross, 5.91 ft. (1.8 m) Length||
|9642||Hioki 9642 Straight Ethernet LAN Cable, 16.41 ft. (5 m) Length||
|9709||Hioki 9709 AC/DC Current Sensor, 500A, Solid Core, with PL23 10-Pin Adapter||
|9709-05||Hioki 9709-05 AC/DC Current Sensor, 500A, Solid Core, with ME15W 12-Pin Adapter||
|CT6700||Hioki CT6700 High Sensitivity Current Probe From 1mA, 50MHz Bandwidth||
|CT6701||Hioki CT6701 High Sensitivity Current Probe From 1mA, 120MHz Bandwidth||
|CT6841||Hioki CT6841 AC/DC Current Sensor, 20A, Split Core, with PL23 10-Pin Adapter||
|CT6841-05||Hioki CT6841-05 AC/DC Current Sensor, 20A, Split Core, with ME15W 12-Pin Adapter||
|CT6843||Hioki CT6843 AC/DC Current Sensor, 200A, Split Core, with PL23 10-Pin Adapter||
|CT6843-05||Hioki CT6843-05 AC/DC Current Sensor, 200A, Split Core, with ME15W 12-Pin Adapter||
|CT6862||Hioki CT6862 AC/DC Current Sensor, 1000A, Solid Core, with PL23 10-Pin Adapter||
|CT6862-05||Hioki CT6862-05 AC/DC Current Sensor, 1000A, Solid Core, with ME15W 12-Pin Adapter||
|CT6863||Hioki CT6863 AC/DC Current Sensor, 200A, Solid Core, with PL23 10-Pin Adapter||
|CT6863-05||Hioki CT6863-05 AC/DC Current Sensor, 200A, Solid Core, with ME15W 12-Pin Adapter||
|CT6865||Hioki CT6865 AC/DC Current Sensor, 1000A, Solid Core, with PL23 10-Pin Adapter||
|CT6865-05||Hioki CT6865-05 AC/DC Current Sensor, 1000A, Solid Core, with ME15W 12-Pin Adapter||
|CT9900||Hioki CT9900 Conversion Cable for 10-pin to 12-pin Sensor Connectors||
|L1000||Hioki L1000 Voltage Cords, 1000V, Alligator clips, 8 Pack, 9.84 ft. (3 m) Length||
|L6000||Hioki L6000 Optical Connection Cable for Sync Control||
|L9217||Hioki L9217 Connection Cord with Insulated BNC Connectors, 5.25 ft. (1.6 m) Length||
|L9438-50||Hioki L9438-50 Voltage Cord, Black/Red, 2 Alligator Clips, 9.84 ft. (3 m) Length||
|Data Sheet:||(5.49 MB)|