Hioki 3505
1kHz, 100kHz, and 1MHz Component Measuring Instrument

  • Enhanced repeatability measurement accuracy, so fittest for production line
  • A self-calibration function minimizes variations in measurement values due to changes in ambient temperature
  • The cable-length-compensation function minimizes measurement errors when the measurement cable is extended
  • Contact errors while measuring can be detected by the Chatter Detection function
  • High-speed measurements in as little as 2 ms, measuring frequency of 1kHz, 1 MHz
  • BIN function, for easy component screening
  • Comparator function and Trigger-synchronized output function, for production line use
Click here for a larger image of the Hioki 3505 1kHz, 100kHz, and 1MHz Component Measuring InstrumentClick for larger image - Hioki 3505
Hioki 3505 Shown
Product Information
Datasheet 953 KB PDF
Click here for Information Regarding PDF'sPDF Help
Measured parameters C (Capacitance), D (dissipation factor tan δ), Q (1/tan δ)
Measurement frequencies 1 kHz, 100 kHz and 1 MHz
Accuracy: ±0.01% or better
Frequency shift: 1 MHz ±1%, ±2%
Measurement signal level Open-circuit terminal voltage: 500 mV or 1 V
Signal level accuracy: ±10% ±5 mV
Output resistance: Approx. 1Ω (@1 kHz in 2.2 μF and higher ranges; @100 kHz in the 22 nF and higher ranges), approx. 20 Ω (in ranges other than the above)
Range of measureable values C: 0.000 fF to 15.0000 μF
D: 0.00001 to 1.99999
Q: 0.0 to 19999.9
Equivalent circuit mode Series-Parallel Equivalent Circuit mode (Auto/Manual)
Measurement time Representative value: 2 ms (FAST)
(Actual measurement time depends on measurement configuration settings)
Measurement speed FAST, NORMAL and SLOW
Averaging function 1 to 256
Low-C Reject function Bad Contact Detection (open circuit between terminals)
Chatter Detection function Bad Contact Detection (chatter)
Current Detection Circuit Monitoring function A measurement signal fault is detected when external noise causes measurement levels to be out of tolerance for the measurement range.
Applied Voltage Value Monitoring function An error is detected when voltage monitored across a test sample is outside of the judgment standard.
Trigger function Internal and external triggers can be enabled
Trigger Delay 0 to 9.999 s
Memory function Up to 1,000 measurement values can be stored in the instrument
(Downloadable by GP-IB and RS-232C)
Panel save and load 70 setting configurations can be stored
Load method: key operation or external I/O
Interface RS-232C, GP-IB and EXT I/O
Operating temperature
and humidity
0 to 40°C, 80% RH or less (non-condensating)
Storage temperature
and humidity
-10 to 55°C, 80% RH or less (non-condensating)
Operating environment Indoors, to 2000 m ASL
Power supply Selectable 100, 120, 220 or 240 V ±10%, 50/60 Hz
Max. power consumption 40 VA
Dimensions Approx. 260 W × 100 H × 298 D mm (exc. projections)
Weight Approx. 7.2 lbs
Ordering Information
Model Description Buy Online Price
3505 Hioki 3505 1kHz, 100kHz, and 1MHz Component Measuring C HiTester Buy Now $8,415.00
Included Accessories
  • 1 - User's Manual
  • 1 - Power Cord
  • 1 - Spare Fuse
Optional Accessories
1196 Hioki 1196, Recording Paper (for 9442 / 25m, 10 rolls) Buy Now $125.00
9140 Hioki 9140 Four Terminal Probe for LCR Buy Now $310.00
9143 Hioki 9143 Pincher Probe for LCR Discontinued
See: L2001
9151-02 Hioki 9151-02 GP-IB Connector Cable (2 Meter) Buy Now $399.00
9261 Hioki 9261 Test Fixture for LCR Buy Now $990.00
9262 Hioki 9262 Test Fixture (Direct Connection Type) Buy Now $615.00
9263 Hioki 9263 SMD Test Fixture (Direct Connection Type) Buy Now $1,225.00
944303 Hioki 9443-03 Printer AC Adapter Discontinued
9444 Hioki 9444 Connection Cable (for 9442) Buy Now $109.00
9677 Hioki 9677 SMD Test Fixture for LCR Buy Now $1,395.00
9699 Hioki 9699 Test Fixture Buy Now $1,635.00