|
|
<< Hameg OscilloscopesHameg HM1508-2
150 MHz Analog/Digital Mixed Signal Combiscope
|
- 1 GSa/s Real Time Sampling, 10 GSa/s Random Sampling
- 1 MPt memory per channel allows Memory Zoom up to 50,000:1
- Frequency spectrum display with FFT
- 4 channels (2 analog, 2 logic inputs), Time Base 50 s/cm – 5
ns/cm
- Pre/Post Trigger -100 % to +400%
- 8-Bit Low Noise Flash A/D Converters
- Acquisition modes: Single Event, Refresh, Average,
- Envelope, Roll, Peak-Detect
- USB-Stick and USB/RS-232 Interface, optional: IEEE-488,
Ethernet/USB
- Signal display: Yt, XY and FFT; Interpolation: Sinx/x, Pulse, Dot
Join (linear)
- Analog mode: as HM1000-2, but 150MHz
|
 
Hameg HM1508-2 Shown
|
|
|
|
Specifications |
| Channels |
Analog |
2 |
| Digital |
2+2 Logic Channels |
| Operating Modes |
Analog: |
CH 1 or CH 2 separate, DUAL (CH 1 and
CH 2 alternate or chopped), Addition |
| Digital: |
Analog Channels: CH 1 or CH 2 separate,
DUAL (CH 1 and CH 2), Addition
Logic Channels: CH 3 and CH4 |
| Y in XY-Mode: |
CH 1 |
| Invert: |
CH 1, CH 2 |
| Bandwidth (-3dB) |
2 x 0 - 150 Mhz |
| Rise Time: |
<2.3 ns |
| Overshoot: |
Max. 1 % |
| Deflection Coefficient (CH 1, 2): 14 calibrated steps |
| 1mV - 2mVcm (10 MHz) |
±5% (0-10 MHz (-3dB) |
| 5mV - 20V/cm |
±3% (1-2-5 sequence) |
| Variable (uncalibrated): |
> 2.5:1 to > 50V/cm |
|
Inputs CH1,2: |
| Impedance: |
1MΩ
// 15pF |
| Coupling: |
DC, AC, GND |
| Max. Input Voltage: |
400V (DC + peak AC) |
| Y Delay Line (analog): |
70 ns |
| Measuring Circuits: |
Measuring Category |
| Digital Mode
only: |
| Logic Channels: |
CH 3, CH 4 |
| Select. switching thresholds: |
TTL, CMOS, ECL |
| User definable thresholds: |
3 |
| within the range |
-2 V to +3 V |
| Analog mode
only: |
| Auxiliary input: |
CH 4: 100V DC = peak AC |
| Function: |
Extern Trigger, Z (unblank) |
| Coupling: |
AC, DC |
| Max. input voltage: |
100V DC + peak AC |
|
General Information |
| Test Voltage: |
approx. 7Vrms
(open Circuit), approx. 50 Hz |
| Test current: |
max. 7 mArms
(short circuit) |
| Reference Potential: |
Ground (safety earth) |
| Probe ADJ Output: |
1 kHz/1 MHz square wave signal 0.2 Vpp |
| Trace Rotation: |
Electronic |
| Line Voltage: |
105 - 253V, 50/60Hz, CAT II |
| Power Consumption: |
47 Watt at 230V, 50 Hz |
| Dimensions: |
285 x 125 x 380 mm |
|
|
|
)
PDF Help