- Wireless Bench Multimeter
- Amp readings behind a sealed blower door
- More accurate diagnosis w/live data
- Monitor system while making adjustments
- 75' wireless signal range
- Transmitter and clamp included
- Works with any accessory head
- Microamps DC - Flame Rectification Tests
- Silicone Leads with Detachable Probe Tips
- Tilt Stand and Magnetic Hanger
- Bright Blue Backlight
- MAX/MIN hold
- Volts AC / Volts DC
- Resistance (Ohms)
- Diode Test
- Rugged ABS case with rubber boot
- Auto power-off (APO) to conserve battery life
The Fieldpiece LT17AW Digital Multimeter is loaded with the parameters and ranges HVACR professionals need for HVACR troubleshooting, plus it receives measurements wirelessly from any of the Fieldpiece Accessory Heads when connected to the wireless transmitter that's included. You can now easily measure current, resistance, voltage, capacitance, frequency, continuity, and temperature either directly, or wirelessly from up to 75' away.
Because of the wireless capability you can connect your amp clamp and completely close the blower door so you get a more accurate amperage reading. Or you can set up a wet bulb measurement in the attic and get live readings while you're making adjustments at the condenser.
Designed specifically for HVACR field service, the LT17AW combines wireless readings with specific features and benefits that HVACR field service pros need.
Transforms any Fieldpiece Accessory Head into a Wireless Device
There is a Fieldpiece accessory head available for just about any job. There are heads to measure temperature, superheat, subcooling, RH%, wet bulb, dew point, vacuum (microns of mercury), manometer (inches of water column), amps AC&DC, high voltage, CO, %CO2, air velocity, and many more.
Transmitter and ACH4 Clamp
Now with the wireless LT17AW all accessory heads can be used either directly through tests leads, or wirelessly with the ET2W wireless transmitter that's included with your LT17AW.
If you were doing lab testing, these features would probably drive you crazy. Weve heard from more than one HVACR veteran that these features really remind you of what youre doing and theyve avoided potentially dangerous situations in the field. The Hi-V LED and beeper let you know when youve hooked up to a circuit over 30V. The continuity LED and beeper tells you if a circuit is open or closed.
Using the detachable test leads and the accessory head amp clamp, read 0-400 amps directly on your meter.
Measure microfarads on motor-run and motor-start capacitors using this range. Disconnect the capacitor from power first. Short the terminals to discharge the capacitor. Disconnect any resistors that might be between the terminals of the capacitor and measure to check for degradation.
Take ambient air or refrigeration line temperatures and more with the built-in K-type port and the included ATB1 wrap tab thermocouple. Add a wet sock (saturated tissue or a shoelace to take wet bulb temperatures. The built-in temperature junction offers great temperature compensation for more accurate and faster measurements.
|AAT3||Fieldpiece AAT3 In-Duct Hot-wire Anemometer & Psychrometer Accessory Head||
|AAV3||Fieldpiece AAV3 Air Velocity and Temperature Accessory Head||
|ACH4||Fieldpiece ACH4 Current Clamp Accessory Head, 400AAC||
|ACM4||Fieldpiece ACM4 Carbon Monoxide Detector Accessory Head||
|ADMN2||Fieldpiece ADMN2 Dual-Port Manometer Accessory Head||
|AMN2||Fieldpiece AMN2 Manometer Accessory Head||
|AOX2||Fieldpiece AOX2 Combustion Check Accessory Head||
|ARH4||Fieldpiece ARH4 Digital Sling Psychrometer Accessory Head||
|ARH5||Fieldpiece ARH5 In-Duct Psychrometer Accessory Head||
|ASX14||Fieldpiece ASX14 Superheat and Subcooling Accessory Head||
|ATH4||Fieldpiece ATH4 Dual-Temperature Accessory Head||
|ATIR3||Fieldpiece ATIR3 Infrared Temperature Accessory Head||
|AUA2||Fieldpiece AUA2 Milliamps & Microamps Accessory Head||
|AVG2||Fieldpiece AVG2 Digital Vacuum Micron Gauge Accessory Head||
|AVH1||Fieldpiece AVH1 AC/DC Voltage Accessory Head||