AEMC Catalog | AEMC Price List

<< AEMC AC Current Probes

AEMC MN200 Series
AC Current Probes

AEMC MN210 AC Current Probes

• Small, compact size
• Large jaw opening accommodated conductors up to 250MCM
• Designed for DMMs, loggers, recorders and oscilloscopes
• Conforms to IEC1010, 600V, Cat. III

The MN210 is a general purpose AC current probe, which is designed for DMMs and other measuring instruments with current input. It has a 1000:1 ratio and an output of 1mA per Amp in the primary (inside the jaw). The MN210 has jack outputs that accept 4mm banana plugs.

AEMC MN210 Shown

AEMC MN211 AC Current Probes

• Small, compact size
• Large jaw opening accommodated conductors up to 250MCM
• Designed for DMMs, loggers, recorders and oscilloscopes
• Conforms to IEC1010, 600V, Cat. III

 The MN211 is a general purpose AC current probe, which is designed for DMMs and other measuring instruments with current input. It has a 1000:1 ratio and an output of 1mA per Amp in the primary (inside the jaw). The MN211 has integral 5 ft (1.5m) leads terminated shrouded banana plugs.

AEMC MN211 Shown

AEMC MN212 AC Current Probes

• Small, compact size
• Large jaw opening accommodated conductors up to 250MCM
• Designed for DMMs, loggers, recorders and oscilloscopes
• Conforms to IEC1010, 600V, Cat. III

 The MN212 is a general purpose AC current probe, which is designed for DMMs and other measuring instruments with current input. It has a 1000:1 ratio and an output of 1mA per Amp in the primary (inside the jaw). The MN212 has jack outputs that accept 4mm banana plugs. The MN212 has protective diodes across the output that limit the voltage in the case if the open secondary.

AEMC MN212 Shown

AEMC MN213 AC Current Probes

• Small, compact size
• Large jaw opening accommodated conductors up to 250MCM
• Designed for DMMs, loggers, recorders and oscilloscopes
• Conforms to IEC1010, 600V, Cat. III

The MN213 is a general purpose AC current probe, which is designed for DMMs and other measuring instruments with current input. It has a 1000:1 ratio and an output of 1mA per Amp in the primary (inside the jaw). The MN213 has integral 5 ft (1.5m) leads terminated by shrouded banana plugs. The MN213 has protective diodes across the output that limit the voltage in the case if the open secondary.

AEMC MN213 Shown

AEMC MN250 AC Current Probes

• Small, compact size
• Large jaw opening accommodated conductors up to 250MCM
• Designed for DMMs, loggers, recorders and oscilloscopes
• Conforms to IEC1010, 600V, Cat. III

 The MN250 is a general purpose AC current probe with voltage output. It is designed for use with DMMs or with measuring instruments with voltage inputs. These probes permit the measurement or recording of current with instruments without current ranges. The voltage output is proportional to the current measured (through the jaws). The MN250 offers a voltage output of 1mV per Amp measured. The MN250 has jack outputs that accept 4mm banana plugs.

AEMC MN250 Shown

AEMC MN251 AC Current Probes

• Small, compact size
• Large jaw opening accommodated conductors up to 250MCM
• Designed for DMMs, loggers, recorders and oscilloscopes
• Conforms to IEC1010, 600V, Cat. III

The MN250 is a general purpose AC current probe with voltage output. It is designed for use with DMMs or with measuring instruments with voltage inputs. These probes permit the measurement or recording of current with instruments without current ranges. The voltage output is proportional to the current measured (through the jaws). The MN250 offers a voltage output of 1mV per Amp measured. The MN291 has integral 5ft (1.5m) leads terminated by shrouded banana plugs.

AEMC MN251 Shown

AEMC MN252 AC Current Probes

• Small, compact size
• Large jaw opening accommodated conductors up to 250MCM
• Designed for DMMs, loggers, recorders and oscilloscopes
• Conforms to IEC1010, 600V, Cat. III

The MN252 is a general purpose AC current probe with voltage output. It is designed for use with DMMs or with measuring instruments with voltage inputs. These probes permit the measurement or recording of current with instruments without current ranges. The voltage output is proportional to the current measured (through the jaws). The MN252 offers a voltage output of 10mV per Amp measured. The MN252 has jack outputs that accept 4mm banana plugs.

AEMC MN252 Shown

• Small, compact size
• Large jaw opening accommodated conductors up to 250MCM
• Designed for DMMs, loggers, recorders and oscilloscopes
• Conforms to IEC1010, 600V, Cat. III

The MN253 is a general purpose AC current probe with voltage output. It is designed for use with DMMs or with measuring instruments with voltage inputs. These probes permit the measurement or recording of current with instruments without current ranges. The voltage output is proportional to the current measured (through the jaws). The MN253 offers a voltage output of 10mV per Amp measured. The MN291 has integral 5ft (1.5m) leads terminated by shrouded banana plugs.

AEMC MN253 Shown

• Small, compact size
• Large jaw opening accommodated conductors up to 250MCM
• Designed for DMMs, loggers, recorders and oscilloscopes
• Conforms to IEC1010, 600V, Cat. III

The MN254 is a high sensitivity probe with voltage outputs (100mV/A and 10mV/A) and combine two switch-selectable ranges of 20A and 200A, thus permitting accurate measurements at low and high levels. The MN254 has jack outputs that accept 4mm banana plugs.

AEMC MN254 Shown

• Small, compact size
• Large jaw opening accommodated conductors up to 250MCM
• Designed for DMMs, loggers, recorders and oscilloscopes
• Conforms to IEC1010, 600V, Cat. III

 The MN255 is a high sensitivity probe with voltage outputs (100mV/A and 10mV/A) and combine two switch-selectable ranges of 20A and 200A, thus permitting accurate measurements at low and high levels. The MN255 has integral 5ft (1.5m) leads terminated by shrouded banana plugs.

AEMC MN255 Shown

• Small, compact size
• Large jaw opening accommodated conductors up to 250MCM
• Designed for DMMs, loggers, recorders and oscilloscopes
• Conforms to IEC1010, 600V, Cat. III

The MN290 is a general purpose AC current probe with voltage output. It is designed for use with DMMs or with measuring instruments with voltage inputs. These probes permit the measurement or recording of current with instruments without current ranges. The voltage output is proportional to the current measured (through the jaws). The MN290 offers a VDC output of 100mVDC per AAC and may be used with loggers or other instruments with DC voltage input. The MN290 has jack outputs that accept 4mm banana plugs.

AEMC MN290 Shown

• Small, compact size
• Large jaw opening accommodated conductors up to 250MCM
• Designed for DMMs, loggers, recorders and oscilloscopes
• Conforms to IEC1010, 600V, Cat. III

The MN291 is a general purpose AC current probe with voltage output. It is designed for use with DMMs or with measuring instruments with voltage inputs. These probes permit the measurement or recording of current with instruments without current ranges. The voltage output is proportional to the current measured (through the jaws). The MN291 offers a VDC output of 100mVDC per AAC and may be used with loggers or other instruments with DC voltage input. The MN291 has integral 5ft (1.5m) leads terminated by shrouded banana plugs.

AEMC MN291 Shown